Contact Us

Home > General > Setup.ampedwireless.com

Setup.ampedwireless.com

Enter the network ID and security key for your extended network. batelco 112.481 görüntüleme 3:02 Amped Wireless SR10000 High Power Wireless-N 600mW Smart Repeater and Range Extender Marketing Video - Süre: 3:56. Click on Connect. Push-button configuration does not detect the connection. this contact form

The Home Network may be a dual band wireless router. Try solution (a) before trying solution (b), etc. Move the Range Extender closer to your Home Network and try again. ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.6/ Connection to 0.0.0.6 failed.

The Range Extender supports WPS connections, however, some companies may use proprietary code for their own push button configurations. Make sure your computer is connected to the Smart Repeater using the included Ethernet cable. Access http://setup.ampedwireless.com and run through the Wizard again.

Connect to your Range Extender and try to access http://setup.ampedwireless.com using your web browser. Make sure the output power is at 100%. You can also set a static channel number on your router to prevent this from happening again in the future. It is recommended that your Home Network shows a signal strength of 70% or greater in the Smart Setup Wizard SCAN results.

Bu videoyu Daha Sonra İzle oynatma listesine eklemek için oturum açın Ekle Oynatma listeleri yükleniyor... Here are the steps to set up the REC10 Wifi Range Extender on an existing network. Reboot the Range Extender by unplugging the Range Extender and plugging it back in. http://www.ampedwireless.com/support/model/rec22a.html Network devices connected to the wired ports of the Range Extender do not have Internet access.

You may be downloading from the Internet and not within your Home Network or Extended Network. After that, you will need to wait about 2 minutes. Check to see if your connection has been reestablished by viewing a website. I received an Error when running the Smart Setup Wizard.

  • If you are connecting to a dual band router, both networks (2.4GHz and 5.0GHz) should have a signal strength of 70% or greater.
  • Once you have it, connect to the Range Extender using an Ethernet cable.
  • To access from the web menu: More Settings > Management > Save/Reload Settings > Save Settings to File After the firmware updates, load your saved settings to keep your existing configurations.

Files transferred through the Internet are limited by your ISP speed and the data download speeds from the website that you are downloading from.

Disable the 5GHz wireless band. Changes to the router could be a result of several events, such as a power outage. All rights reserved. 1) Like Us 2) Follow Us Follow @ampedwireless 3) Newsletter Signup Rest assured, your information is private.

Date of Purchase: January February March April May June July August September October November December 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 http://idroprofessional.com/general/setup-wm.html Go to the Smart Features tab in the web menu and access the Wi-Fi Coverage Controls. Check the connections of the Antennas to the Range Extender. You need to adjust your Time Zone Settings from the Management Web Menu page.

ThioJoe 14.801.387 görüntüleme 9:25 Amped Wireless R10000G Wireless Router : In Depth Review - Süre: 13:47. Products ALLY Wi-Fi System HD Wi-Fi Cameras TAP Series Routers Range Extenders Access Points Adapters Indoor ProSeries ProSeries Switches Outdoor ProSeries Outdoor Antennas Antennas & Boosters Powerline A/V Net Connect Bluetooth Please try the request again. navigate here Check to see if your connection has been reestablished by viewing a website.

While connected to the Range Extender, open your web browser and access http://setup.ampedwireless.com. Check that the antenna is connected securely to the antenna connector. I cannot find my Home Network when scanning for Wi-Fi networks in the Wizard.

You may have a DNS issue and the Range Extender is not obtaining the IP settings from your Home Network.

If your Home Network uses a dual-band router, it will not work with the Range Extender. To access from the web menu: More Settings > Management > Save/Reload Settings > Save Settings to File After the firmware updates, load your saved settings to keep your existing configurations. I have a dual-band router and I cannot extend the network (or both networks). Amped Wireless 15.920 görüntüleme 7:26 homemade wifi antenna extender - Süre: 7:38.

You may be too far away from your Home Network. The system returned: (22) Invalid argument The remote host or network may be down. If you are able to go online then this is not a problem. http://idroprofessional.com/general/setup-hlp.html On the SCAN page, your Home Network should show a signal strength of 70% or greater.

The connection to the Home Network seems slow. Check to see that your Home Network router’s DHCP server is enabled. Double check that you have the correct security key to connect to the Home Network. Check that the antenna is connected securely to the antenna connector.

I cannot find my Home Network when scanning for wireless networks in the Smart Setup Wizard. It is recommended that your Home Network shows a signal strength of 70% or greater in the Wizard SCAN results. Wi-Fi Protected Setup (WPS) is not working. View Read Me.txt 4/12/2016 v1.19 Recent Updates Improved connection stability to Home Network.